AS400 agent not active
AS400 agent not active
After IPL AS400 machine, subsystem "CMAGENT" found 1 job "AT" is missing.
Suppose in AS400 subsytem should see as below ;
CMAGENT
AG -PGM-P-CTMAG
AR -PGM-P-CTMAR
AT -PGM-P-CTMAT (Not Active)
*When run Diagnostic found ' Agent ping to Control-M/Server : Failed" ,
Your help is very much appreciated.Thank You.
Suppose in AS400 subsytem should see as below ;
CMAGENT
AG -PGM-P-CTMAG
AR -PGM-P-CTMAR
AT -PGM-P-CTMAT (Not Active)
*When run Diagnostic found ' Agent ping to Control-M/Server : Failed" ,
Your help is very much appreciated.Thank You.
Verify if CTM Server is reacheable from AS400 system.
Verify if any hard coded IP address is used.
Verify the Agent Settings
1 Use the CHGCURLIB command, as follows:
2 Set the Agent environment, using the CTMAGINIT command, as follows:
CHGCURLIB <Agent>
CTMAGINIT <Agent>
Verify CTM SERVER HOSTNAME in CONFIGURATION
To invoke utility CTMAGCFG:
1 Specify command CTMAGCFG and press F4. The CONTROL-M/Agent
Configuration (CTMAGCFG) screen is displayed with the current configuration
values.
2 Modify the Agent operating parameters, as required, and press Enter.
Verify if any hard coded IP address is used.
Verify the Agent Settings
1 Use the CHGCURLIB command, as follows:
2 Set the Agent environment, using the CTMAGINIT command, as follows:
CHGCURLIB <Agent>
CTMAGINIT <Agent>
Verify CTM SERVER HOSTNAME in CONFIGURATION
To invoke utility CTMAGCFG:
1 Specify command CTMAGCFG and press F4. The CONTROL-M/Agent
Configuration (CTMAGCFG) screen is displayed with the current configuration
values.
2 Modify the Agent operating parameters, as required, and press Enter.
Screen capture from PROCLOG.
Browse : /home/ctm/CMAGENT/PROCLOG/ctmag_20101229.log
Record : 1 of 2 by 18 Column : 1 59 by 131
Control :
....+....1....+....2....+....3....+....4....+....5....+....6....+....7....+....8....+....
************Beginning of data**************
1229 103420 19 AGENT STARTED AT 20101229103420
1229 122439 19 AGENT STARTED AT 20101229122439
************End of Data********************
Browse : /home/ctm/CMAGENT/PROCLOG/ctmag_20101229.log
Record : 1 of 2 by 18 Column : 1 59 by 131
Control :
....+....1....+....2....+....3....+....4....+....5....+....6....+....7....+....8....+....
************Beginning of data**************
1229 103420 19 AGENT STARTED AT 20101229103420
1229 122439 19 AGENT STARTED AT 20101229122439
************End of Data********************
1. Enable DEBUG - set to level 4
2. Set the Communication Trace parameter to 1 using CTMAGCFG utility
3. Log on as the CONTROL-M/Agent user profile and run CTMAGSTOP
4. Log on as the CONTROL-M/Agent user profile and run CTMAGSTART
5. Verify the following
Server-to-Agent TCP/IP port
Agent-to-Server TCP/IP port
6. Run CTMAGPING
7. Review PROCLOG and check for detailed error messages
2. Set the Communication Trace parameter to 1 using CTMAGCFG utility
3. Log on as the CONTROL-M/Agent user profile and run CTMAGSTOP
4. Log on as the CONTROL-M/Agent user profile and run CTMAGSTART
5. Verify the following
Server-to-Agent TCP/IP port
Agent-to-Server TCP/IP port
6. Run CTMAGPING
7. Review PROCLOG and check for detailed error messages